What are your ideas about Tools You Need to Install a New Bathtub ?
Installing a bathtub isn't specifically brain surgery, however it does require solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is also a reasonably tough job. If the old tub is conveniently obtainable, the job can move speedily; if you need to open a wall to get rid of the old tub and place the new bathtub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly need a helper to vacate the old tub and also set in the new one. Make certain you have certified on your own for the job and also are comfortable attempting it. As opposed to hiring a contractor to take over a halfway-completed project, it is far better to consider using one before you start. Possibilities are you may require a professional plumber to make tube links.
This short article will certainly assist you mount a new tub in your bathroom if you have actually already acquired a new bathtub and do not need to alter the setup of your previous supply of water pipelines.
Your devices and product list ought to consist of the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, activate the faucets to drain any type of water continuing to be in the system. The procedure of getting rid of the existing taps can be fairly problematic because of the limited access that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a towel all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have actually been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing substance.
Prior to going on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making sure that the washing machines remain in location in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous type ought to be linked to the tap ends first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Using the two wooden boards under its feet, position the bath tub in the called for placement. The wood boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 little factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub till the level reads degree.
To set up taps, fit all-time low of the outermost flexible faucet port to the suitable supply pipeline by making a compression sign up with; then do the very same for the other tap.
Activate the supply of water and inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Load the tub and also examine the overflow outlet and also the typical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bath tub should wait till the bathtub has actually been utilized at least when as this will resolve it right into its final placement.
Getting ready for the Installment
First of all, the supporting framework supplied with the bathroom ought to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets device to avoid pressure on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be suited its final setting.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to break a stiff seal, creating the water to pass through the wall between the bath as well as the tiling, bring about complications with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes and also cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the motion experienced when the tub is in use. The sealant can split relatively very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our part about Tools You Need to Install a New Bathtub . Thanks so much for taking time to read our piece of content. Liked our content? Please share it. Let somebody else find it. I treasure reading our article about Installing A Bathtub.
Request An Estimate